Sunday, February 17, 2013

Postcard 1, 2, 3's-An Easy Postcard Tutorial




So, while experimenting with these little quilts I have learned a few things:

1. I don't like double sided fusible-like the effect but the process is painful.
2. They don't need to be perfect-just pleasing
3. I love doing them-instantaneous joy at the completion
4. They use up nicely those bits of fabrics left over from paper piecing that are too small for regular quilts.
5. They are addicting!

Step 1      Gather Materials

Peltex: I used Peltex double sided fusible heavy duty.  There are several products out there that will do the trick.  The Peltex made a nice firm card that ironed flat and wasn't too thick.

Double sided lightweight interfacing: if you feel the need

Glue sticks: The one I used was acid free and went on blue but turned clear

Material:  Thematic prints, batiks (worked well with the raw edge applique technique because they didn't fray as much as the regular). Also a plain cotton for the back-light color.

Scrapbooking stuff:  You know you have it:)  Most of my quilting friends scrapbook as well or at least used to.   Stamps/inks (Check the dollar bins at Michaels) also, I found the large "Postcard Stamp" at Road to CA for 14.00.  I am sure it could be bought on line-but it isn't necessary-you can draw it on.  Cardstock, charms, yarn/ribbon, stickers, beads, buttons, words, pens, colored pencils, etc.

Iron and Ironing pad, Sewing machine, embroidery thread, an ironing sheet for applique is nice but not essential, Rotary cutter and mat.

Gather supplies into one area so they are easily accessible
Step 2   Cut Base of postcard

Cut Peltex with rotary cutter and mat into 4x6 inch rectangles.  My roll was 24 inches wide so I cut it into 6 inch strips and then cut each strip every 4 inches so I got 6 postcard blanks every 6 " or 18 postcards for 1/2 yard of Peltex.

Cut Base material with rotary cutter and ruler into 6" strips then cut every 4 "



Step 3  Stamp your backside (not your backside-the card backside)

I stamped quite a few of these ahead of time so I didn't have to stop and make a back.  Cut your light colored plain cotton 4.5x6.5 so it overlaps a bit.  Then either stamp with your postcard stamp or lay it aside to write on after the card is complete.

Cut material 4 1/2 x 6 1/2

blot don't rub ink onto large stamp


Center stamp onto material




Postcard backing complete-set aside





Step 4  Choose your fabric base and pieces for postcard

The St. Patrick's day post card was a solid base with pieces cut out of another thematic fabric after it had been ironed onto double sided lightweight fusible.  The 2nd side of the fusible was then scored with the tip of a scissors or pin and backing is peeled off and then piece is stuck to base piece and ironed down.

Pieces are selected

second side of double sided fusible is scored

plastic from fusible is peeled off

Pieces are ironed down individually and colored pencil is being applied
Another way to add fabrics to the front is with glue.  All the tutorials I read said to use fusible interfacing but I am going to do it my way  because it is just faster and less tedious-either way will work.  I used an acid free glue stick and just went over the back of each piece-careful to glue the background before the foreground.  Since I am going to stitch everything down-I don't see why it would matter. Let me know if you have a reason that it matters that I don't see.

Pieces selected from paper piecing scraps

Same pieces glued down starting from back and moving forward



I decided I liked the looks of the purple mountains fabric backside up.  It gives that smoky look at dusk that I wanted.  Our Santa Maria Valley has 5 mountain peaks when viewed from the north end looking toward the southwest and the mountains are very rocky-hence the blue squares on the purple mountains. The sun sets behind them and we have beautiful red sunsets.  Anyway-the block is securely attached and now I will take it to the machine using decorative thread.

Step 5 Machine Quilt

all stitched down

from the back


Step 6  Trimming
Trimming can be done two ways, by hand or with a rotary cutter.  There are pros and cons to both.  Rotary cutting gives a nice clean edge but if not careful you can nic the postcard.  Hand cutting gives you more control but is not quite as clean as the rotary.

Iron backing on, let cool, line up card and cut with a rotary cutter


Trim front even with card with sharp scissors





iron back to trimmed front




back peeks out about 1/4 inch all around




hand trim flush to edge or rotary cut with ruler and blade


Step 7  Finish Edge


Set your machine to zigzag.  I like a thin edge that is tightly sewn-personal choice.  I set my machine to 3.0 mm width and 0.3 length and go around the card 2 times.


machine set to 3.0 x 0.3




finished card
back of card
This back is made from a preprinted quilt label from Kaufman-I printed the lettering and the lines






Last Step  Put in a plastic sleeve and mail

You can have the post office hand cancel the postcard and then put it in a sleeve to keep it safe-tape back down securely.

 
ready for mailing








nature inspired

Valentine's Day

Mother's Day

St. Patrick's Day
I hope you have enjoyed the tutorial.  I only ask that you not copy my original designs.  You can surely do better:)

2 comments:

Quiltedtime said...

Wow! That was certainly complete. You did a fantastic job, Elaine.

twila cox said...

Thank you for such a great idea...I have two illnesses and I am on several groups for support think I just found a way to encourage someone else...and feel like I have one something...off to look for postcard stamp..Twila